Install a Wall-Mounted Fireplace

Safe & Simple

Le Feu Fires Canada · Guide

A wall-mounted bioethanol fireplace delivers real flames and Scandinavian elegance without a chimney or gas line. This step-by-step guide covers planning, tools, mounting, and safety best practices for installing a fixed, wall-hung model like the Le Feu Wall Dome. Always follow your specific product manual and local regulations.

Plan: wall type, clearances, and height

Proper planning ensures a secure, long-lasting installation and optimal viewing. Le Feu’s wall-mounted bioethanol fireplaces are certified to ANSI/CAN/UL/ULC 1370 for indoor use when installed and operated as directed.

  • Wall type: Mount only on solid brick or concrete. Do not mount directly on drywall or hollow partitions without proper structural reinforcement.
  • Clearances: Keep the unit away from curtains, soft furnishings, and combustible décor. Maintain recommended side/top clearances from your manual.
  • Viewing height: Center the dome roughly at seated eye level for living rooms (commonly 95–115 cm from finished floor to center; adjust to your space).
  • Location: Avoid strong drafts and high-traffic zones. Ensure normal room ventilation.
  • Power/gas: Not required; the unit is flueless and runs on liquid bioethanol fuel.
Measuring and marking a wall for a fireplace bracket
Measure twice, drill once: mark bracket holes level and confirm clearance before mounting.


Tools and hardware

Wall-mounting screws and anchors are not typically included. Select hardware that matches your wall construction and load requirements.

Essential tools

  • Drill/driver with masonry bits
  • Level and measuring tape
  • Pencil and masking tape
  • Stud/structure finder (if applicable)
  • Socket or screwdriver set
  • Vacuum and safety glasses

Hardware (choose by wall type)

  • Concrete/brick anchors and matching screws
  • Heavy-duty structural fixings if mounting on reinforced framing
  • Washers per bracket spec

Included with fireplace

  • Mounting bracket (model-specific)
  • Fireplace dome and hinge assembly
  • Bioethanol burner with SafeBurn insert
  • Damper tool and user manual


Mount the bracket (step-by-step)

  1. Mark the position. Tape a paper template or hold the bracket at the desired height. Use a level to mark hole centers.
  2. Pre-drill. Use the correct masonry bit size for your anchors. Vacuum dust for clean seating.
  3. Insert anchors. Tap anchors flush with the wall surface; follow anchor manufacturer instructions.
  4. Fix the bracket. Align, add washers if required, and drive screws snugly. Re-check level before fully tightening.
  5. Load check. Gently pull on the bracket to verify a firm, wobble-free hold.
A level, solidly fixed bracket is essential. If unsure about structural integrity, consult a qualified installer.


Hang the dome and fit the burner

With the bracket secure, attach the dome assembly per your manual. Many models include a hinge that lets you rotate the dome up to 90° left or right for directing heat and ambience.

  • Lift the dome onto the bracket with a helper.
  • Confirm the hinge pin and safety fasteners are fully engaged.
  • Place the SafeBurn burner in its cradle; confirm it is level and seated.
  • Keep combustibles clear of the flame window; add a heat-resistant surface below if required by the manual.
Close-up of a wall-mounted fireplace detail
Attach the dome securely; confirm hinge operation and safety fasteners before fueling.


Fueling, test burn, and safety checks

Use only approved bioethanol fuel. Read the safety instructions on the bottle and in your fireplace manual. Typical output for Le Feu models is approximately 2.0–3.0 kWh, with 2–3 hours of burn per litre depending on damper setting and conditions.

First ignition

  1. Confirm the burner is cool and the damper is open (if applicable).
  2. Using a funnel, fill to the indicated maximum. Wipe spills immediately.
  3. Ignite with a long lighter. Keep hands and sleeves clear.
  4. Observe the flame for a few minutes; check for stability and proper ventilation.

Safety checks

  • Maintain normal room ventilation; do not operate in sealed spaces.
  • Keep a minimum clearance from soft furnishings and décor.
  • Extinguish with the damper tool; allow at least 30 minutes to cool before refueling.
  • Never move the fireplace while lit or warm.


Care and maintenance

Bioethanol fireplaces are low maintenance. Routine care keeps your unit looking pristine and operating smoothly.

  • When cool, wipe the dome exterior with a damp, lint-free cloth.
  • Clean the burner using a soft cotton cloth lightly moistened with bioethanol.
  • Store fuel upright, capped, and away from heat sources and sunlight.
  • Inspect fixings and bracket tightness periodically.


Quick FAQ

Can I mount on drywall?

Mount only on solid brick or concrete. Do not install directly on drywall or hollow walls unless a qualified professional provides structural reinforcement.

Are screws included?

No. Use anchors and screws suitable for your wall type to ensure a secure installation.

Do I need a chimney or vent?

No. Bioethanol fireplaces are flueless; normal room ventilation is sufficient when operated as directed.

How high should I mount it?

Aim for seated eye level in living spaces (often 95–115 cm to the dome center). Adjust to your layout and viewing preference.

Is indoor use certified?

Le Feu bioethanol fireplaces are certified to ANSI/CAN/UL/ULC 1370 for indoor use when installed and operated per the manual.

Explore Wall-Mounted Fireplaces by Le Feu

Discover certified, eco-friendly designs that add Scandinavian warmth and save floor space.

Shop All Wall Fireplaces Browse More Guides

Back to Learn